X Marks the Scot - An on-line community of kilt wearers.

   X Marks Partners - (Go to the Partners Dedicated Forums )
USA Kilts website Celtic Croft website Celtic Corner website Houston Kiltmakers

User Tag List

Page 1 of 3 123 LastLast
Results 1 to 10 of 24

Hybrid View

  1. #1
    Join Date
    15th October 09
    Location
    Dallas area
    Posts
    1,184
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Latest commision

    Hi all,

    Got this far enough along that I think it will come out all right. This being the second attempt. First one's file work didn't turn out all that good.

    Starting off with some of Devin Thomas's stainless banded ladder damascus -



    Add into this some stabilized bog oak -



    This is the first piece of damascus but it shows the piece laid out -



    Trimmed out and drilled -



    Fitted with the bolsters and slabbed bog oak -



    I have to finish the sides of the handle material to keep the file work intact -


  2. #2
    Join Date
    15th October 09
    Location
    Dallas area
    Posts
    1,184
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Got the file work laid out. This one is getting file work all the way wrapped around the handle -



    The first pass -



    Second pass -



    The third pass -



    Cleaned up. Just three simple steps to a vine and thorns file work -







    The butt end. I played around here and planned it out so it look like two vines meeting -



    After heat treat and etching. Did a new technique here. First deep etched in muriatic acid and than followed up with a dip in ferric chloric to bring out the contrast. Turned out the best that I've ever gotten -



    Next will be the handle and sheath, with a lot of luck.

    Jim

  3. #3
    Join Date
    2nd October 07
    Location
    Denver, Colorado- a mile high, baby!
    Posts
    6,147
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)
    Holy crap!! That file work is awesome!!
    "Two things are infinite- the universe, and human stupidity; and I'm not sure about the universe." Albert Einstein.

  4. #4
    Join Date
    26th March 08
    Location
    Atlanta, GA
    Posts
    2,254
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Yeah...

    D@mn...

    Brilliant!

  5. #5
    Join Date
    16th September 10
    Posts
    1,387
    Mentioned
    47 Post(s)
    Tagged
    0 Thread(s)
    I was reading along, amazed as usual, yeah, yeah, stunning as always, even if I got myself up and in the shop it would never look a quarter that good, but seeing it, I ought to. THEN I got to the thorns picture and Nighthawk's emoticon's were a picture of my face. That's just not possible. I've handled files, I'm competent with tools, but that's just not possible. There are no more words. Stunning, awesome, stupendous, we've used them before. As you say, though this goes beyond. I've just used 1500 hundred words to say I have no words, and it's NOT EVEN FINISHED YET!!!

  6. #6
    Join Date
    4th February 11
    Location
    Ionia, MI
    Posts
    200
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Dddduuuudddddeeeeee!!!!!!!!!!!!!

    Do you have a website or something you sell these on? Cuz ya should!

    Seriously sweet work!

    Always -Steve

  7. #7
    Join Date
    22nd December 10
    Location
    Virginia
    Posts
    4,157
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    So seriously...I'm going to have to get one of these someday. Sooner than later, hopefully.

  8. #8
    Join Date
    19th May 08
    Location
    Oceanside CA
    Posts
    3,491
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    "Just three simple steps to a vine and thorns file work. . ."

    Reminds me of the Far Side cartoon where the scientist is standing at a chalkboard filled with an esoteric calculation. About the middle of the calculation is a part that reads "and here the magic happens!"

    Definitely magic. Stupendously beautiful magic!

    See you on Sunday, Jim -- safe travels!
    Proudly Duncan [maternal], MacDonald and MacDaniel [paternal].

  9. #9
    Join Date
    15th October 09
    Location
    Dallas area
    Posts
    1,184
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Thanks all. Trust me there are better makers out there but if you want this is were I learned how to do file work -

    http://www.centercross.com/cciv/?p=F...Dwayne_Dushane

    Just that and the dreaded P & D words, practice and destroy. Lots of destroy. Just "destroyed" up $100 of damascus in "practice" on the first time with this blade.

    Quote Originally Posted by sydnie7 View Post
    "Just three simple steps to a vine and thorns file work. . ."

    Reminds me of the Far Side cartoon where the scientist is standing at a chalkboard filled with an esoteric calculation. About the middle of the calculation is a part that reads "and here the magic happens!"
    Just for the record, that was sarcasm on my part. That is the way the video first covered it. "Yah right!" was my first thought.

    Jim

  10. #10
    Join Date
    5th August 08
    Location
    Lancashire, England
    Posts
    4,345
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    That is stupendous. Really. fantastic stuff.

Page 1 of 3 123 LastLast

Similar Threads

  1. Latest Addition
    By Une in forum Miscellaneous Forum
    Replies: 22
    Last Post: 23rd August 09, 12:15 PM
  2. Our Latest Geezers
    By davedove in forum Celebration Zone
    Replies: 11
    Last Post: 17th July 09, 03:34 AM
  3. Latest Acquisition
    By londonpiper in forum Show us your pics
    Replies: 18
    Last Post: 27th September 08, 08:28 AM
  4. Our Latest
    By Freelander Sporrano in forum Show us your pics
    Replies: 15
    Last Post: 6th February 05, 01:12 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

» Log in

User Name:

Password:

Not a member yet?
Register Now!
Powered by vBadvanced CMPS v4.2.0