Kilt Flashes

[Sherry]

I would suggest trying some of the sealant on a scrap of fabric. Some sealants turn whitish, & you don't want that on a finished project. :-o

Sherry

[Luke MacGillie]

Then there is always just a length of inch to inch and a quarter wool twill tape, enough to wrap around the top of the hose twice and tie in a nice bow knot. It can be something that matches your hose or just plain old red.

But then again I really dislike the non diced or tartan hose, looks too much like bobby socks for me.

[Rick]

I would suggest trying some of the sealant on a scrap of fabric. Some sealants turn whitish, & you don't want that on a finished project. :-o

Sherry

As with most chemicals used on fabric, testing is probably not a bad idea. I have used Dritz "Fray Check." While the formulation used to make up what is in my bottle does not turn white, there is no guarantee that they will not change the formulation. I use so little of it, I will probably have this bottle for years more.

Rick

[David Thornton]

For those of us who are sewing challanged, is there a good source for flashes? I would like to get several solid colors.
David

[GlassMan]

I got my solid flashes from SportKilt. Part of the reason is that they're inexpensive. Another is that many inexpensive flashes I've found are simply a piece of ribbon while the one's at SportKilt.com are felt and look more like wool. Also, some other cheap flashes I've seen have some hard sheet sewn inside and they wind up getting bent outward and staying that way.

Finally, the one's at SportKilt are the only inexpensive ones I've seen that use a clasp closure instead of Velcro. I have velcro on flashes. It always get's snagged on my hose. The clasps are the way to go.

[Sherry]

You can just Google "kilt flashes" & get lots of hits. But I have made ribbon ones as per the instructions in the earlier link I gave. They are very simple & can even be sewn by hand. They cost pennies compared to purchased ones, & you can easily have a whole "wardrobe" of flashes.

On another note, after looking more carefully at Rick's method, I think that I would just sew or serge the strip of fabric (width of finished flash x 2 + seam allowances) into a tube, leaving a long thread tail for turning (trim the seam allowances to about 1/4" if they are wider than that). This makes all the stitches hidden on the inside. Press the tube flat with the seam in the middle back. Then you can turn down the top & trim the bottom just as Rick describes.

Sherry

[Rick]

On another note, after looking more carefully at Rick's method, I think that I would just sew or serge the strip of fabric (width of finished flash x 2 + seam allowances) into a tube, leaving a long thread tail for turning (trim the seam allowances to about 1/4" if they are wider than that). This makes all the stitches hidden on the inside. Press the tube flat with the seam in the middle back. Then you can turn down the top & trim the bottom just as Rick describes.

Sherry

Great minds must think alike. I just purchased some wool fabric that is too light of weight to make flashes by the method I described. I was thinking about doing it as you suggest.

My new Hector Russell kilt just arrived and it included tartan flashes. They simply serged the edges with a thread colour that matched the line in respective line in the tartan. This looks fine. However, I only have a straight stitch sewing machine.

[Sherry]

The HR flashes sound interesting, but I'm thinking that, as a commercial producer, they have sergers set up with different colors of thread on them. It would be a pain to change the thread color for something small like flashes, but it could certainly be done.

Sherry

[Colin]

I have made a pair or two using grosgrain ribbon, and velcro. All I have done is cut the ribbon into flahes and added velcro the the back. I than use a strip of velcro (male and female sewn together so that it wraps around my calf and attaches) as the garter. Very easy to do and supplies can be found really cheap at any place that sells fabric (I got all this at Walmart for under $10 and have enough ribbon for a few more sets). This way you can also make numerous flashes in various colours or tartan and can just change them up with the same garters.

Here's some pics:

[michael steinrok]

I would suggest trying some of the sealant on a scrap of fabric. Some sealants turn whitish, & you don't want that on a finished project. :-o

Sherry

Man she thinks of everything