The homemade sporran adventure...

[Mattg]

It looks great! I've been wanting to try that myself! So I'm interested to see what plans and tools etc. you use.

[ozmeath]

Thanks Mike. you got me to double check the materials and luckily it's all solid leather. It's quite an old one, from the early 70's I can guess.The side piece I'll have to but as there's not quite enough of the thiner leather in it to use. What weight/grade do you recomend Mike?
Matt so far I've basically just used those tools you see there. I did make a 1:1 design on paper. I found the center line, folded it, opened and charcoaled half of the piece and folded again to check symmetry.
I then re-charcoaled it and rubbed it on the leather itself to get an impession to cut out.
that's about it so far.

[Mattg]

Sweet! I'm going to go find an old leather briefcase!

[Kilted KT]

Looks good so far. Can't wait to see the final product.

[GMan]

I think my favorite part of the pictures is the drawings you have placed with the work in progress. Good luck, and so far so good.

[Mike S]

What weight/grade do you recomend Mike?

Glad to hear it's 100% leather, I guess my Dad was cheap when he bought his (We're talking 1960's vintage in my case)! As far as the gusset sides, you could use a 2 to 4 oz lining leather, pigskin, suede, buckskin etc. depending on what's available to you and the final finish you are going for. Any supple, lighter weight leather will do, however since you have a smooth finish on the front and back pieces, you should shoot for something with the scarf skin still intact i.e. vegetable tanned lining leather and not a split, napped, suede finish. Since the pieces you have cut from the case are already stained and finished, it might require a bit of experimentation with the stain and final leather treatment/sheen finish to get a good match. I'd experiment with some scraps of your chosen leather before committing to the finish on the final item.

With this type of Sporran design, it is best to sew the gusset with the outer face against the finished side of the front, then turn it back over the edge toward the rear of the sporran to sew to the back. This will give the rounded, neat looking lip around the front edge and is one of the reasons the gusset piece must be soft and thin enough to do so neatly.

As a fellow silversmith, I know you'll already have many of the skills and craftsmanship to jump right into this without any difficulty. However if you want any help along the way, feel free to let me know as I've made a lot of sporrans over the years.

[ozmeath]

Many thanks guys, glad you're all along for the ride. Mike that was a good affirmation of the process. Had the same design in mind with the gusseting. Found a suitable weight piece for that, but have to cut it down the middle length-wise as it's wide but not long enough. also it's a bit shinier and slightly darker than the satin/matt finnish of the front/back. I hit it with a no 6 brass suede brush to dull it a little, tho still not quite up to the same patina. the test piece frayed if I went too hard with the brush. also I'm not too sure about the staining. Put a bevelled edge on the flap and front secondary pieces (see pic). The finish is quite sealed so I was of course gonna use test pieces to get the right finish. The front secondary bits are to cover the marks left from the original clasps.


E.

[Freelander Sporrano]

This brings back memories of when Sten Rune and I started. We made our first sporran out of cornflakes packets and bin bags... Looks like your project is comming on well....Have fun

[Alan H]

ONe thing I love about this gang is that so many of us just set out and try new stuff...making sporrans, making sgian dubhs, making kilts and we share in information with the board.

It really makes X Marks a fantastic and creative place. GOOD ON YA for doing this and showing us how it's going.

[cloves]

Ozmeath,

what do you plan on doing with the old briefcase hardware? I suspect you're gonna incorporate that silver clasp from the other thread to use on this sporran. So will you keep that old hardware for another project?